Menu

0

$0.00

 
 

 

AEM Series 2 P&P EMS 95-05 2G DSM Mitsubishi Evo 8 4G63T

Description

This is a standalone ECU for 2g DSM / Eclipse applications listed below. This ecu completely replaces the factory ecu... read more

SKU:
30-6310
Categories:
,
Brand:
AEM
Weight:
7 lbs
view all details

Price

$2,490.84 $1,793.40

Quantity

- +

Total

$2,490.84 $1,793.40

0 reviews

Compare

- +

Description

This is a standalone ECU for 2g DSM / Eclipse applications listed below. This ecu completely replaces the factory ecu and controls every aspect of the engine. We use it on almost every project we do because it performs excellently at a reasonable price. 


The series 2 EMS has some new features over the Series 1 box. It’s a all new platform that is no longer tied to the GEMs hardware. The new unit has 12 peak and hold injectors so a resistor box is no longer needed. It runs in direct fire so wasted spark is no longer used and a smoother, factory quality idle can be had. It uses either a serial port or usb so hunting around for older laptops will be a thing of the past. The internal logging has an increased capacity. With the series two you can password protect your maps so if your tuning and don’t want your work looked by others you have that option. It will work with the existing gauges so your AEM wideband or serial gauge will be a direct transition. 


Key Features:


Plug n Play
Full Fuel and Timing Control, Full Standalone, Fully Adjustable
Factory Sensors OK
Factory Sensors can be retained, however if they need to be changed, (like upgrading to a bigger map sensor), AEM has a full line of sensors available and we stock them!
Basemap Included
Password Protection
Direct Fire Ignition (no resistor box required)
16 General Outputs
8 General Inputs
Use these inputs to log various additional sensor readings (Wideband, Air Temp, Fluid Pressure, etc). These inputs can also be used to trigger fail-safes for boost, meth/water/alcohol injection, and much more
4 EGT Inputs (for fuel control)
Internal Logging Memory
Log data straight to the computer and review the session with your laptop all from within the computer.
FULL IDLE CONTROL
Customizable Traction Control
Full Boost Control (with optional boost control solenoid)
3-Step Launch Control
Nitrous Control
Definable Knock Control
USB Compatible
and more…

Series 2 Plug & Play Engine Management System
 

AEM’s Series 2 EMS is a complete engine control system that plugs into the factory harness and uses the factory sensors. This means you do not need to replace any parts of the harness or sensors, just plug the EMS into the harness and begin tuning! The Series 2 EMS allows you to control every aspect of your engine. From rev limit, timing, adding different sized injectors, boost control, nitrous injection, even anti-lag and individual cylinder fuel and timing trims, the Series 2 EMS gives you total control from an easy to use interface.

Outputs
Injector Outputs 6 Peak & Hold, 6 Saturated
Coil Outputs 6
Selectable direct drive or 0-5V Coil Output Yes
Direct plug in, no jumper harness required Yes
General purpose LS outputs 12
General purpose HS outputs 4
Individual cylinder ignition trims Yes
Individual cylinder fuel trims Yes
Inputs
Trigger inputs (Ref/Sync) 4
Analog voltage inputs 18
Configurable Analog/RTD/Thermister inputs 4
Switch inputs 5
Lambda inputs 2x
Knock sensors 2
User adjustable knock sensor center frequency Yes
Communication
USB comms Yes
RS232 comms Yes
Communication cables included Yes
Fully enabled editing/logging software included Yes
CAN bus equipped Yes
RS232 datastream output 19 ch
CAN datastream output 19 ch
Communicates with AIM Dash/Dataloggers Yes
Communicates with Racepak Dash/Dataloggers Yes
DATA Acquisition
Internal data logging 1 MB
Maximum internal logging rate (per channel) 250 Hz
PC logging Yes
Data analysis using AEMLog Yes
Functions and Features
All channels/maps/tuning options unlocked Yes
Boost control Yes
Groundspeed based boost target Yes
Staged injection Yes
Ground speed limiting Yes
Rate of Acceleration Control Yes
Overrun boost enhancement (anti-lag) Yes
Gear change ignition cut (shift-without-lift) Yes
Password protected calibrations Yes
Fuel & Ignition rev limiters Yes
“In cockpit” global fuel trim capability Yes
Gear dependent shift light Yes
Evap/Purge function Yes
DC Motor control 2 Ch
Software definable “virtual” switch inputs 2
EGT Based fuel trims Yes
Maximum boost limit None
Physical Dimensions
Length 192 mm
With 150 mm
Height 37 mm
Finish Black Anodized

AEM Series 2 Plug-N-Play Engine Management Systems
– Legal in California only for racing vehicles which may never be used upon a highway.

This product fits the following vehicles:

  • 1995 to 1999 Mitsubishi Eclipse GST 2.0L Turbo
  • 1995 to 1999 Mitsubishi Eclipse GSX 2.0L Turbo
  • 2000 to 2002 Mitsubishi Eclipse RS, GS 2.4L 4 Cyl
  • 2003 to 2005 Mitsubishi EVO VIII 2.0L Turbo

 

Additional information

Weight
7 lbs

Reviews (0)

Be the first to review “AEM Series 2 P&P EMS 95-05 2G DSM Mitsubishi Evo 8 4G63T”

  • There are no reviews yet.

Vehicle Fitment

Make Model Year
Mitsubishi Eclipse GST 1995 - 1999
Mitsubishi Eclipse GSX 1995 - 1999
Mitsubishi Eclipse RS 2000 - 2002
Mitsubishi Evo 8 2003 - 2005